{"id":1265,"date":"2026-10-30T01:23:44","date_gmt":"2026-10-30T01:23:44","guid":{"rendered":"https:\/\/zhhmarinefender.com\/?p=1265"},"modified":"2026-10-30T13:37:20","modified_gmt":"2026-10-30T13:37:20","slug":"what-is-a-yokohama-fender","status":"publish","type":"post","link":"https:\/\/zhhmarinefender.com\/de\/what-is-a-yokohama-fender\/","title":{"rendered":"Was ist ein Yokohama Fender?"},"content":{"rendered":"<p class=\"font-claude-response-body break-words whitespace-normal leading-[1.7]\">A Yokohama fender is a floating pneumatic rubber fender: an air-filled marine fender used between a vessel and a jetty, or between two vessels alongside each other, whose energy absorption depends on diameter, length and initial internal pressure rather than on the brand name it carries. Fenders of this class are built and tested to <a href=\"https:\/\/www.iso.org\/standard\/59873.html\">ISO 17357-1:2014<\/a>, which covers high-pressure units at 50 kPa and above and defines two pressure grades, P50 and P80. The name is used loosely across the industry, so the label alone tells a buyer very little. Which unit belongs at a given berth depends on vessel displacement, approach velocity at first contact, and the reaction force the berth structure can accept.<\/p>\n<h2 dir=\"ltr\">What Is a Yokohama Fender, and Why the Name Says Little<\/h2>\n<p dir=\"ltr\">The Yokohama fender name covers a family of floating pneumatic rubber fenders, not one fixed product, and whether a given unit suits a berth turns on its size and pressure grade. Yokohama Rubber states that it developed its floating fender in 1958 from its tyre and aircraft fuel-tank rubber technology. The <a href=\"https:\/\/zhhmarinefender.com\/history-of-yokohama-fenders\/\">history of the name<\/a> explains how one maker&#8217;s product became the label for a whole class. The precise term is floating pneumatic rubber fender, or Yokohama-type pneumatic fender. Listings often spell it yokahama or yokohoma; these refer to the same product. Yokohama is also still a company name, so a buyer checking provenance should confirm the actual manufacturer and the ISO documentation. The term itself proves no origin.<\/p>\n<p dir=\"ltr\">Treating the name as a single specification is the expensive mistake. Two units carrying it can differ by an order of magnitude in the energy they absorb and in the force they push back into a hull.<\/p>\n<p dir=\"ltr\">A pressure grade carried over from an earlier project, because the vessel class looked similar, is the common route to that error. The fender arrives correctly marked and still returns more reaction force into the berth than the structure was designed to take. The first corrective step is to repeat the fender-system selection against verified berth data. Depending on what that shows, the outcome may be a different pressure grade, a different size, more units, a revised arrangement, or a limit on approach speed.<\/p>\n<p dir=\"ltr\" data-sourcepos=\"13:1-13:517;1948-2464\"><img fetchpriority=\"high\" decoding=\"async\" class=\"alignnone wp-image-2358 size-full\" src=\"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender.webp\" alt=\"Floating Yokohama-type pneumatic fender, an air-filled rubber body with an end flange at each end\" width=\"800\" height=\"600\" srcset=\"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender.webp 800w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-300x225.webp 300w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-768x576.webp 768w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-16x12.webp 16w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/p>\n<h2 dir=\"ltr\">How a Yokohama Fender Works: Air as the Working Medium<\/h2>\n<p dir=\"ltr\">A Yokohama fender absorbs impact by compressing sealed air, so its energy absorption, hull pressure and failure mode all trace back to one variable: the internal pressure it holds at the moment of contact. An inner rubber layer seals the air, synthetic cord-reinforced layers carry the load, an abrasion-resistant outer layer takes the wear, and end flanges close each end and carry the inflation valve. ISO 17357-1:2014 requires fenders of 2,500 mm diameter and larger to carry a safety valve that releases excess pressure during accidental over-compression. Smaller sizes may carry one where the order calls for it.<\/p>\n<p dir=\"ltr\">Air also lets the fender conform to a hull as it compresses, spreading the contact so that hull pressure and reaction force stay comparatively low. That matters most where two hulls meet obliquely, as they do in <a href=\"https:\/\/zhhmarinefender.com\/ship-to-ship-transfer\/\">ship-to-ship work<\/a>. Yokohama Rubber&#8217;s product information states that energy absorption of its pneumatic fenders does not decrease under inclined compression up to 15 degrees. Any other maker&#8217;s unit has to show that in its own type-approval data.<\/p>\n<p dir=\"ltr\">Pressure in a sealed body of roughly fixed volume rises and falls with absolute temperature. A fender inflated on a cool quayside and then left in direct sun has drifted from the pressure it was set to. So the measurement procedure belongs in the specification: take and interpret readings with the manufacturer&#8217;s inspection and temperature-correction method. Temperature can explain part of a change. It does not excuse a reading outside the manufacturer&#8217;s temperature-adjusted limits. The safety valve answers a different event, accidental over-compression, which is mechanical.<\/p>\n<h2 class=\"text-text-100 mt-3 -mb-1 text-[1.125rem] font-bold\" dir=\"ltr\" data-sourcepos=\"23:1-23:58;4540-4597\">Pneumatic Against Foam and Solid: Where Each Type Wins<\/h2>\n<p class=\"font-claude-response-body break-words whitespace-normal\" dir=\"ltr\" data-sourcepos=\"25:1-25:254;4599-4852\">A pneumatic Yokohama fender is usually the stronger candidate for large vessels and oblique ship-to-ship contact, depending on unit size and inspection access. Foam or solid rubber can fit better elsewhere, and the table shows where.<\/p>\n<div dir=\"ltr\">\n<table>\n<thead>\n<tr>\n<th scope=\"col\">What it decides<\/th>\n<th scope=\"col\">Pneumatic (Yokohama-type)<\/th>\n<th scope=\"col\">Foam-filled<\/th>\n<th scope=\"col\">Solid rubber<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Behaviour under overload<\/td>\n<td>Reaction force rises progressively, within rated compression and valve capacity<\/td>\n<td>Progressive<\/td>\n<td>Can stiffen toward a rigid block<\/td>\n<\/tr>\n<tr>\n<td>Hull pressure<\/td>\n<td>Low, spread across the contact<\/td>\n<td>Low<\/td>\n<td>Tends to be higher for comparable energy<\/td>\n<\/tr>\n<tr>\n<td>Oblique \/ STS contact<\/td>\n<td>Holds performance under inclined compression<\/td>\n<td>Good<\/td>\n<td>Falls off as the angle grows<\/td>\n<\/tr>\n<tr>\n<td>What puts it out of service<\/td>\n<td>Loss of air through a breach in the skin<\/td>\n<td>Skin damage; no air to lose<\/td>\n<td>Wear, and failure at the fixings<\/td>\n<\/tr>\n<tr>\n<td>Routine attention<\/td>\n<td>Periodic pressure checks<\/td>\n<td>Minimal<\/td>\n<td>Minimal<\/td>\n<\/tr>\n<tr>\n<td>Typically suits<\/td>\n<td>Large vessels, STS, wide tidal range<\/td>\n<td>Smaller sizes, limited inspection access<\/td>\n<td>Fixed quay faces<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p dir=\"ltr\">The table gives screening-level tendencies for narrowing a shortlist. Design energy, contact area, tidal range, abrasion, puncture risk or whole-life cost can overturn any row at a particular berth.<\/p>\n<p dir=\"ltr\">The overload row repays following through. As a solid rubber fender nears its practical compression limit, further deflection can make reaction force climb steeply. That load lands in the hull plating and the quay face. A pneumatic body keeps a more gradual force curve further into the stroke, within its rated compression, its flange design envelope and its safety valve&#8217;s venting capacity. So the binding question on a pneumatic unit is usually the force it returns. Sizing up is no automatic safety margin.<\/p>\n<p dir=\"ltr\">At the smaller end of the range, and at berths where nobody will check pressure on a schedule, a <a href=\"https:\/\/zhhmarinefender.com\/the-difference-between-pneumatic-fenders-and-foam-filled-fenders\/\">foam-filled unit<\/a> is often the better buy. There is no air to lose. At that scale both types can usually be sized for the energy involved, and cost comparisons run both ways with size and quantity.<\/p>\n<h2 dir=\"ltr\">Net Type or Sling Type: Matching the Fitting to How the Fender Will Be Handled<\/h2>\n<p dir=\"ltr\">A Yokohama fender&#8217;s fitting type is a separate decision from its size and pressure grade, and it turns on how often the unit moves and how much abrasion the berth puts on it. Net type fenders sit inside a chain, wire or fibre net, usually with tyres or rubber sleeves, which suits fixed and semi-permanent positions where abrasion is the main threat. Sling type units carry a lifting device at each end connected by guy chain or rope. They weigh less and are quicker to recover and redeploy. Among the <a href=\"https:\/\/zhhmarinefender.com\/different-types-of-pneumatic-fenders\/\">ISO 17357 fender types<\/a>, these are Type I (net) and Type II (sling), alongside a single-ended net variant, Type I Single, whose far end carries no flange or metalwork.<\/p>\n<p dir=\"ltr\" data-sourcepos=\"46:1-46:470;7326-7795\"><img decoding=\"async\" class=\"alignnone wp-image-2359 size-full\" src=\"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-net-sling-types.webp\" alt=\"Diagram contrasting how net type and sling type Yokohama fenders are fitted and secured\" width=\"800\" height=\"450\" srcset=\"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-net-sling-types.webp 800w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-net-sling-types-300x169.webp 300w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-net-sling-types-768x432.webp 768w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-net-sling-types-18x10.webp 18w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/p>\n<p dir=\"ltr\">The practical question is redeployment frequency against abrasion exposure. A fender that stays on one berth for years earns its net. One that moves between operations, or gets recovered ahead of weather, is easier to live with as a sling type, provided the lifting arrangement on site can handle it.<\/p>\n<p dir=\"ltr\">Two body variants reach contact points a horizontal unit cannot. Yokohama Rubber lists a vertical pneumatic fender that can be water-ballasted for vessels whose berthing point is below the waterline. Hydro-pneumatic fenders from several makers serve submarines and other deep-draught, low-freeboard hulls. For a ballasted unit, the datasheet should state the certification route; the family name implies none.<\/p>\n<p dir=\"ltr\">On tidal berths with a wide water-level swing, the guy chain and the end-fitting shackles tend to be the parts that come up for re-inspection first. They carry the cyclic movement the fender body is there to absorb. How that fitting is then rigged, meaning chain length, attachment points and stand-off geometry, is a separate exercise from choosing the fender and belongs with the berth&#8217;s installation drawings.<\/p>\n<h2 class=\"text-text-100 mt-3 -mb-1 text-[1.125rem] font-bold\" dir=\"ltr\" data-sourcepos=\"54:1-54:56;8664-8719\">Where Yokohama Fenders Are Used: STS, Berth Faces and Offshore Work<\/h2>\n<p dir=\"ltr\">Yokohama fenders work in three settings, ship-to-ship transfer, berthing against a quay or jetty, and offshore operations alongside floating units, and the variable to confirm first differs in each. What loads the fender changes between settings, so a unit chosen for one needs re-checking for another.<\/p>\n<p dir=\"ltr\">In ship-to-ship transfer the fender sits between two moving hulls. The units are usually rigged on one ship and recovered between operations, which favours light net or sling fittings. One contact loads both hulls, so the hull pressure limit that binds is the lower of the two ships&#8217; limits. That limit may belong to the ship without the fenders.<\/p>\n<p dir=\"ltr\"><img decoding=\"async\" class=\"size-full wp-image-2332 aligncenter\" src=\"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/Yokohama-fenders-in-a-ship-to-ship-transfer.webp\" alt=\"Floating pneumatic fenders positioned between two tankers during a ship-to-ship transfer operation\" width=\"800\" height=\"600\" srcset=\"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/Yokohama-fenders-in-a-ship-to-ship-transfer.webp 800w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/Yokohama-fenders-in-a-ship-to-ship-transfer-300x225.webp 300w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/Yokohama-fenders-in-a-ship-to-ship-transfer-768x576.webp 768w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/Yokohama-fenders-in-a-ship-to-ship-transfer-16x12.webp 16w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/p>\n<p dir=\"ltr\">At a quay or jetty, one vessel approaches a structure that does not yield. The reaction force the structure can accept is then often the first limit to check, unless the vessel class carries a low hull pressure limit. Fenders there tend to stay in place for long periods, which favours net types.<\/p>\n<p dir=\"ltr\">Offshore, alongside an FPSO or a floating terminal, swell turns one berthing into many contacts. Wear on the net, guy chain and end fittings then accumulates with the number of contacts, so an inspection interval set by date alone can fall behind the real load history.<\/p>\n<h2 dir=\"ltr\">Sizing and Pressure: Which Variable to Confirm First<\/h2>\n<p dir=\"ltr\">Sizing a Yokohama fender starts from berthing energy, not from a diameter, and berthing energy is set by the vessel&#8217;s displacement, its approach velocity at first contact, and the contact geometry at the berth. Two documents divide the work. ISO 17357-1:2014 governs the product, including guaranteed energy absorption for standard sizes. Project-level selection is a separate engineering exercise. It follows the berth design criteria and guidance such as the <a href=\"https:\/\/www.pianc.org\/publication\/pianc-fender-guidelines-2024\/\">PIANC Fender Guidelines 2024<\/a> (MarCom WG 211), which supersede the 2002 WG 33 guideline; their <a href=\"https:\/\/www.rivieramm.com\/news-content-hub\/new-global-fender-standards-come-into-force-88507\">transition period ran to 1 May 2026<\/a>. Between the two <a href=\"https:\/\/zhhmarinefender.com\/yokohama-fenders-pressure\/\">initial pressure grades<\/a>, P80 offers higher guaranteed performance at the same nominal size, and it raises reaction force and hull pressure with it. Yokohama Rubber&#8217;s published table puts numbers on that trade for a 1,500 \u00d7 3,000 mm unit. At P80, guaranteed energy absorption rises from 153 to 214 kN\u00b7m, reaction force from 579 to 761 kN, and hull pressure from 132 to 174 kPa. As ratios, about 40 percent more energy costs about 31 percent more force and 32 percent more hull pressure. P80 therefore belongs only where those higher figures still sit inside what the berth structure and the hull can accept.<\/p>\n<p dir=\"ltr\">Approach velocity at first contact is the variable to pin down first. In the basic kinetic relationship behind berthing energy, energy scales with the square of velocity and only linearly with mass, so an assumed approach speed moves the answer further than an assumed tonnage does. Project design energy adds added-mass, eccentricity, softness and configuration coefficients and the required safety factors. The velocity\u2013mass asymmetry survives all of them. The 2024 guidelines strongly recommend site-specific berthing information, and the square law shows why: a measured approach speed moves design energy, up or down, faster than any tonnage correction.<\/p>\n<div dir=\"ltr\">\n<table>\n<thead>\n<tr>\n<th scope=\"col\">Variable<\/th>\n<th scope=\"col\">What it sets<\/th>\n<th scope=\"col\">When to confirm it<\/th>\n<th scope=\"col\">Changeable after manufacture?<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Approach velocity at first contact<\/td>\n<td>Berthing energy, scaling with the square of velocity<\/td>\n<td>First<\/td>\n<td>No<\/td>\n<\/tr>\n<tr>\n<td>Vessel displacement<\/td>\n<td>Berthing energy, scaling linearly<\/td>\n<td>First<\/td>\n<td>No<\/td>\n<\/tr>\n<tr>\n<td>Allowable reaction force at the berth<\/td>\n<td>Constrains the whole system: grade, size, quantity, spacing, arrangement<\/td>\n<td>Before any grade or size is fixed<\/td>\n<td>No<\/td>\n<\/tr>\n<tr>\n<td>Hull pressure limit for the vessel class<\/td>\n<td>Constrains grade, size and contact area<\/td>\n<td>Before any grade or size is fixed<\/td>\n<td>No<\/td>\n<\/tr>\n<tr>\n<td>Diameter and length<\/td>\n<td>Guaranteed energy absorption available<\/td>\n<td>Once the design energy exists<\/td>\n<td>No<\/td>\n<\/tr>\n<tr>\n<td>Fitting type (net or sling)<\/td>\n<td>Handling effort and abrasion resistance<\/td>\n<td>Last<\/td>\n<td>Sometimes, subject to body design, end fittings and manufacturer approval<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p dir=\"ltr\"><img loading=\"lazy\" decoding=\"async\" class=\"alignnone wp-image-2360 size-full\" style=\"font-style: inherit; font-weight: inherit;\" src=\"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-p50-p80-comparison.webp\" alt=\"Diagram showing P80 raising both energy absorption and reaction force against P50 at equal size\" width=\"800\" height=\"450\" srcset=\"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-p50-p80-comparison.webp 800w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-p50-p80-comparison-300x169.webp 300w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-p50-p80-comparison-768x432.webp 768w, https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2026\/06\/yokohama-fender-p50-p80-comparison-18x10.webp 18w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/p>\n<p dir=\"ltr\">Published <a href=\"https:\/\/zhhmarinefender.com\/yokohama-fenders-size\/\">Yokohama fender size ranges<\/a> vary by manufacturer. What decides anything is the guaranteed energy absorption on the datasheet for the specific unit, read against a design energy figure.<\/p>\n<h2 dir=\"ltr\">ISO 17357 Compliance and What to Check on Delivery<\/h2>\n<p dir=\"ltr\">ISO 17357-1:2014 is the standard a Yokohama-type fender is certified against, and it governs the product: material, performance, dimensions, and the test and inspection procedures behind the certificate. It was reviewed and confirmed in 2024 and remains current. Part 2 covers low-pressure fenders. Together the two parts replaced the 2002 edition, so check any other year quoted in a product listing against the current text. PIANC sits on the other side of that line. Its 2024 guidelines are engineering guidance for designing, manufacturing and testing a fender system, not a product certificate. Read a &#8220;PIANC certified&#8221; listing as &#8220;designed or tested in accordance with WG 211&#8221;. It should also name the body that witnessed the tests and the scope covered. <a href=\"https:\/\/zhhmarinefender.com\/pianc-fender-guidelines\/\">What a PIANC claim proves on a quotation<\/a> is a separate matter from the ISO certificate.<\/p>\n<p dir=\"ltr\">Clause 6.1.6 caps the bead ring, and any other steel ringing the flange opening, at under 0.20 times the fender diameter. The aim is that the metal takes no permanent set when the fender is compressed close to 80 percent; net-type (Type I) fenders may omit the bead ring. A clause written around near-80-percent compression treats that load as one a working fender will meet. After a heavy contact, then, the flange and bead area belongs in the manufacturer-approved inspection, whatever the outer skin looks like. The <a href=\"https:\/\/zhhmarinefender.com\/structural-design-of-pneumatic-fenders\/\">structural design of pneumatic fenders<\/a> covers the rest of what the standard fixes in that region.<\/p>\n<p dir=\"ltr\">Unfolding a fender on the quayside and checking it against the order takes an hour. Finding out at the berth that the marked pressure grade differs from the one the berthing-energy calculation assumed costs far more.<\/p>\n<ul dir=\"ltr\">\n<li>ISO 17357-1:2014 conformity marked on the body, with standard and year legible<\/li>\n<li>A prototype test certificate reviewed by a major class society, for tests carried out within the ten years before your enquiry (clause 5.2)<\/li>\n<li>Commercial test records for the delivered units, including air-pressure and hydrostatic results<\/li>\n<li>Nominal size, P50 or P80 grade and serial number, checked against the order<\/li>\n<li>Safety valve fitted on every unit of 2,500 mm diameter or larger, with its setting recorded against the pressure grade; settings and valve design vary between manufacturers<\/li>\n<li>End flange, valve seat, shackles, swivels and net or sling condition once unfolded<\/li>\n<li>Independent inspection or <a href=\"https:\/\/zhhmarinefender.com\/classification-society-in-shipping\/\">classification-society review<\/a> where the purchaser, terminal, charterer or project specification requires it<\/li>\n<\/ul>\n<p dir=\"ltr\">ISO conformity confirms that the product complies. Whether it suits a particular vessel, berth or ship-to-ship operation is a separate engineering call.<\/p>\n<h2 dir=\"ltr\">Two Berth Figures That Bound a Yokohama Fender Order<\/h2>\n<p dir=\"ltr\">Once it is clear what a Yokohama fender is, two figures are the starting inputs for its specification: the approach velocity at first contact, and the reaction force the berth structure can accept. Diameter, pressure grade, quantity and fitting type are then matched against them, along with the hull pressure limit, contact geometry and fender arrangement. A specification that names a size without those inputs has skipped the step that shows whether the fender fits the berth.<\/p>\n<p dir=\"ltr\">Orders that go wrong often start with a diameter picked first. The energy check runs afterwards to justify it, and the check bends to fit the fender. Where a figure depends on the berth, we confirm it at project level; at Zhonghaihang the berthing-energy check and the ISO documentation are part of the specification.<\/p>\n<p dir=\"ltr\">If your approach velocity comes from a generic table and not from pilot or harbourmaster records, settle that figure before comparing any datasheet. If it is already site-measured, set the allowable reaction force and the hull pressure limit beside it. The <a href=\"https:\/\/zhhmarinefender.com\/choose-the-right-yokohama-pneumatic-fenders\/\">Yokohama pneumatic fender selection<\/a> then comes down to matching those three against the guaranteed energy absorption of a specific <a href=\"https:\/\/zhhmarinefender.com\/pneumatic-fenders\/\">Yokohama Fender<\/a> size and grade.<\/p>\n<h2 dir=\"ltr\">FAQ<\/h2>\n<h3 dir=\"ltr\">How much does a Yokohama fender cost?<\/h3>\n<p dir=\"ltr\">Price tracks size, pressure grade, fitting type and order quantity more than anything else, and the spread across the size band is wide. Any figure worth planning against comes from a current quotation for a specific diameter, length and grade.<\/p>\n<h3 dir=\"ltr\">Can a punctured fender be repaired?<\/h3>\n<p dir=\"ltr\">Often, and whether it is worth doing depends on where the damage sits. Damage confined to the outer rubber is a different case from damage reaching the cord layers or the flange seal. Any repair has to restore the pressure boundary itself.<\/p>\n<h3 dir=\"ltr\">How often should internal pressure be checked in service?<\/h3>\n<p dir=\"ltr\">Start with the supplier&#8217;s <a href=\"https:\/\/zhhmarinefender.com\/yokohama-fenders-maintenance\/\">maintenance manual<\/a>. At least one published manual asks for far more than an annual check: Trelleborg&#8217;s calls for a gauge reading on each fender at least four times a year, and before every use in ship-to-ship service. Heavy contact, strong sun or a suspected leak are reasons to check sooner. Keep the readings in a serial-numbered log.<\/p>\n<h3 dir=\"ltr\">Why does the same fender read higher in the afternoon?<\/h3>\n<p dir=\"ltr\">At roughly constant volume, absolute pressure can be approximated as proportional to the absolute temperature of the air inside. A P50 unit set to 50 kPa gauge with its internal air at 15 \u00b0C would read about 66 kPa if that air warmed evenly to 45 \u00b0C (151.3 \u00d7 318.15 \/ 288.15 \u2248 167 kPa absolute). Skin temperature is not internal air temperature, and the grade stays P50 whatever the gauge shows.<\/p>\n<h3 dir=\"ltr\">Does an ISO 17357 certificate cover the classification-society requirement?<\/h3>\n<p dir=\"ltr\">Not automatically. The class-society evaluation behind an ISO 17357-1 prototype certificate covers the model that was tested, not the batch being delivered. A project that asks for class approval or survey of the delivered units still needs that document in its own right.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>A Yokohama fender is a floating pneumatic rubber fender: an air-filled marine fender used between a vessel and a jetty, [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":1269,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"default","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[23],"tags":[20],"class_list":["post-1265","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-pneumatic-fender-technology","tag-fender-systems"],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v28.8 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>What Is a Yokohama Fender? P50 vs P80, ISO 17357 &amp; Sizing<\/title>\n<meta name=\"description\" content=\"A Yokohama fender is a floating pneumatic rubber fender. See how P50 and P80 trade energy for reaction force, what ISO 17357 requires, and how STS use differs.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/zhhmarinefender.com\/de\/what-is-a-yokohama-fender\/\" \/>\n<meta property=\"og:locale\" content=\"de_DE\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"What Is a Yokohama Fender? P50 vs P80, ISO 17357 &amp; Sizing\" \/>\n<meta property=\"og:description\" content=\"A Yokohama fender is a floating pneumatic rubber fender. See how P50 and P80 trade energy for reaction force, what ISO 17357 requires, and how STS use differs.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/zhhmarinefender.com\/de\/what-is-a-yokohama-fender\/\" \/>\n<meta property=\"og:site_name\" content=\"Zhonghaihang Shipping Supply\" \/>\n<meta property=\"article:published_time\" content=\"2026-10-30T01:23:44+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-10-30T13:37:20+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2025\/03\/\u5e94\u7528\u56fe4-1.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"800\" \/>\n\t<meta property=\"og:image:height\" content=\"600\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Ms. kate Zhu\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Verfasst von\" \/>\n\t<meta name=\"twitter:data1\" content=\"Ms. kate Zhu\" \/>\n\t<meta name=\"twitter:label2\" content=\"Gesch\u00e4tzte Lesezeit\" \/>\n\t<meta name=\"twitter:data2\" content=\"14\u00a0Minuten\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/\"},\"author\":{\"name\":\"Ms. kate Zhu\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/#\\\/schema\\\/person\\\/123e7ae319a5d579ab8a2b3ae16326d1\"},\"headline\":\"What is a Yokohama Fender?\",\"datePublished\":\"2026-10-30T01:23:44+00:00\",\"dateModified\":\"2026-10-30T13:37:20+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/\"},\"wordCount\":2822,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/zhhmarinefender.com\\\/wp-content\\\/uploads\\\/2025\\\/03\\\/\u5e94\u7528\u56fe4-1.jpg\",\"keywords\":[\"Fender Systems\"],\"articleSection\":[\"Pneumatic Fender Technology\"],\"inLanguage\":\"de\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/\",\"url\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/\",\"name\":\"What Is a Yokohama Fender? P50 vs P80, ISO 17357 & Sizing\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/zhhmarinefender.com\\\/wp-content\\\/uploads\\\/2025\\\/03\\\/\u5e94\u7528\u56fe4-1.jpg\",\"datePublished\":\"2026-10-30T01:23:44+00:00\",\"dateModified\":\"2026-10-30T13:37:20+00:00\",\"description\":\"A Yokohama fender is a floating pneumatic rubber fender. See how P50 and P80 trade energy for reaction force, what ISO 17357 requires, and how STS use differs.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/#breadcrumb\"},\"inLanguage\":\"de\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"de\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/#primaryimage\",\"url\":\"https:\\\/\\\/zhhmarinefender.com\\\/wp-content\\\/uploads\\\/2025\\\/03\\\/\u5e94\u7528\u56fe4-1.jpg\",\"contentUrl\":\"https:\\\/\\\/zhhmarinefender.com\\\/wp-content\\\/uploads\\\/2025\\\/03\\\/\u5e94\u7528\u56fe4-1.jpg\",\"width\":800,\"height\":600,\"caption\":\"What is a Yokohama Fender\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/what-is-a-yokohama-fender\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/zhhmarinefender.com\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"What is a Yokohama Fender?\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/#website\",\"url\":\"https:\\\/\\\/zhhmarinefender.com\\\/\",\"name\":\"Zhonghaihang Shipping Supply\",\"description\":\"Marine Equipment Supplier\",\"publisher\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/zhhmarinefender.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"de\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/#organization\",\"name\":\"Zhonghaihang Shipping Supply\",\"url\":\"https:\\\/\\\/zhhmarinefender.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"de\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/zhhmarinefender.com\\\/wp-content\\\/uploads\\\/2024\\\/12\\\/cropped-H18758266e39a4912a59f5cfb5d819611a.avif\",\"contentUrl\":\"https:\\\/\\\/zhhmarinefender.com\\\/wp-content\\\/uploads\\\/2024\\\/12\\\/cropped-H18758266e39a4912a59f5cfb5d819611a.avif\",\"width\":512,\"height\":512,\"caption\":\"Zhonghaihang Shipping Supply\"},\"image\":{\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/#\\\/schema\\\/person\\\/123e7ae319a5d579ab8a2b3ae16326d1\",\"name\":\"Ms. kate Zhu\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"de\",\"@id\":\"https:\\\/\\\/zhhmarinefender.com\\\/wp-content\\\/litespeed\\\/avatar\\\/62e20f8cbae27e0d6e902c4e861aef3c.jpg?ver=1794829646\",\"url\":\"https:\\\/\\\/zhhmarinefender.com\\\/wp-content\\\/litespeed\\\/avatar\\\/62e20f8cbae27e0d6e902c4e861aef3c.jpg?ver=1794829646\",\"contentUrl\":\"https:\\\/\\\/zhhmarinefender.com\\\/wp-content\\\/litespeed\\\/avatar\\\/62e20f8cbae27e0d6e902c4e861aef3c.jpg?ver=1794829646\",\"caption\":\"Ms. kate Zhu\"},\"sameAs\":[\"https:\\\/\\\/zhhmarinefender.com\"]}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"Was ist ein Yokohama-Schutzblech? P50 vs. P80, ISO 17357 &amp; Gr\u00f6\u00dfenangaben","description":"Ein Yokohama-Kotfl\u00fcgel ist ein schwimmender, pneumatischer Gummikotfl\u00fcgel. Erfahren Sie, wie P50 und P80 Energie gegen Reaktionskraft tauschen, was ISO 17357 vorschreibt und wie sich die Verwendung von STS unterscheidet.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/zhhmarinefender.com\/de\/what-is-a-yokohama-fender\/","og_locale":"de_DE","og_type":"article","og_title":"What Is a Yokohama Fender? P50 vs P80, ISO 17357 & Sizing","og_description":"A Yokohama fender is a floating pneumatic rubber fender. See how P50 and P80 trade energy for reaction force, what ISO 17357 requires, and how STS use differs.","og_url":"https:\/\/zhhmarinefender.com\/de\/what-is-a-yokohama-fender\/","og_site_name":"Zhonghaihang Shipping Supply","article_published_time":"2026-10-30T01:23:44+00:00","article_modified_time":"2026-10-30T13:37:20+00:00","og_image":[{"width":800,"height":600,"url":"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2025\/03\/\u5e94\u7528\u56fe4-1.jpg","type":"image\/jpeg"}],"author":"Ms. kate Zhu","twitter_card":"summary_large_image","twitter_misc":{"Verfasst von":"Ms. kate Zhu","Gesch\u00e4tzte Lesezeit":"14\u00a0Minuten"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/#article","isPartOf":{"@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/"},"author":{"name":"Ms. kate Zhu","@id":"https:\/\/zhhmarinefender.com\/#\/schema\/person\/123e7ae319a5d579ab8a2b3ae16326d1"},"headline":"What is a Yokohama Fender?","datePublished":"2026-10-30T01:23:44+00:00","dateModified":"2026-10-30T13:37:20+00:00","mainEntityOfPage":{"@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/"},"wordCount":2822,"commentCount":0,"publisher":{"@id":"https:\/\/zhhmarinefender.com\/#organization"},"image":{"@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/#primaryimage"},"thumbnailUrl":"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2025\/03\/\u5e94\u7528\u56fe4-1.jpg","keywords":["Fender Systems"],"articleSection":["Pneumatic Fender Technology"],"inLanguage":"de","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/","url":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/","name":"Was ist ein Yokohama-Schutzblech? P50 vs. P80, ISO 17357 &amp; Gr\u00f6\u00dfenangaben","isPartOf":{"@id":"https:\/\/zhhmarinefender.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/#primaryimage"},"image":{"@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/#primaryimage"},"thumbnailUrl":"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2025\/03\/\u5e94\u7528\u56fe4-1.jpg","datePublished":"2026-10-30T01:23:44+00:00","dateModified":"2026-10-30T13:37:20+00:00","description":"Ein Yokohama-Kotfl\u00fcgel ist ein schwimmender, pneumatischer Gummikotfl\u00fcgel. Erfahren Sie, wie P50 und P80 Energie gegen Reaktionskraft tauschen, was ISO 17357 vorschreibt und wie sich die Verwendung von STS unterscheidet.","breadcrumb":{"@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/#breadcrumb"},"inLanguage":"de","potentialAction":[{"@type":"ReadAction","target":["https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/"]}]},{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/#primaryimage","url":"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2025\/03\/\u5e94\u7528\u56fe4-1.jpg","contentUrl":"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2025\/03\/\u5e94\u7528\u56fe4-1.jpg","width":800,"height":600,"caption":"What is a Yokohama Fender"},{"@type":"BreadcrumbList","@id":"https:\/\/zhhmarinefender.com\/what-is-a-yokohama-fender\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/zhhmarinefender.com\/"},{"@type":"ListItem","position":2,"name":"What is a Yokohama Fender?"}]},{"@type":"WebSite","@id":"https:\/\/zhhmarinefender.com\/#website","url":"https:\/\/zhhmarinefender.com\/","name":"Zhonghaihang Shipping Supply","description":"Lieferant f\u00fcr Schiffsausr\u00fcstung","publisher":{"@id":"https:\/\/zhhmarinefender.com\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/zhhmarinefender.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"de"},{"@type":"Organization","@id":"https:\/\/zhhmarinefender.com\/#organization","name":"Zhonghaihang Shipping Supply","url":"https:\/\/zhhmarinefender.com\/","logo":{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/zhhmarinefender.com\/#\/schema\/logo\/image\/","url":"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2024\/12\/cropped-H18758266e39a4912a59f5cfb5d819611a.avif","contentUrl":"https:\/\/zhhmarinefender.com\/wp-content\/uploads\/2024\/12\/cropped-H18758266e39a4912a59f5cfb5d819611a.avif","width":512,"height":512,"caption":"Zhonghaihang Shipping Supply"},"image":{"@id":"https:\/\/zhhmarinefender.com\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/zhhmarinefender.com\/#\/schema\/person\/123e7ae319a5d579ab8a2b3ae16326d1","name":"Frau kate Zhu","image":{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/zhhmarinefender.com\/wp-content\/litespeed\/avatar\/62e20f8cbae27e0d6e902c4e861aef3c.jpg?ver=1794829646","url":"https:\/\/zhhmarinefender.com\/wp-content\/litespeed\/avatar\/62e20f8cbae27e0d6e902c4e861aef3c.jpg?ver=1794829646","contentUrl":"https:\/\/zhhmarinefender.com\/wp-content\/litespeed\/avatar\/62e20f8cbae27e0d6e902c4e861aef3c.jpg?ver=1794829646","caption":"Ms. kate Zhu"},"sameAs":["https:\/\/zhhmarinefender.com"]}]}},"_links":{"self":[{"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/posts\/1265","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/comments?post=1265"}],"version-history":[{"count":9,"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/posts\/1265\/revisions"}],"predecessor-version":[{"id":2437,"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/posts\/1265\/revisions\/2437"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/media\/1269"}],"wp:attachment":[{"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/media?parent=1265"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/categories?post=1265"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/zhhmarinefender.com\/de\/wp-json\/wp\/v2\/tags?post=1265"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}